GaaribaanEngine rebuilding · Lahore
Reboring · cylinder boring & honing

Engine reboring in Lahore

Oil burning, smoke and low compression can have several causes, and worn cylinders are only one of them. At Standard Automobile Engineering on Samsani Road, your engine is inspected first; once it is opened, every cylinder is measured, and only then is it decided whether it needs honing, reboring or a sleeve, done on the workshop's own machines. Gaaribaan then rebuilds the engine with new pistons and rings to suit the bores, sends photos on WhatsApp and gives a written guarantee.

  • No need to buy another car
  • Machined in our own workshop
  • Every bore measured, before and after
  • Honing, rebore or sleeve, as measured
  • 6-month / 10,000 km guarantee on rebuilds
Three-cylinder engine block with pistons removed
A stripped three-cylinder block: each bore is measured before deciding the work.
Signs

Does your engine need reboring?

These signs often point to worn cylinders, pistons or rings, though valve seals and guides can cause some of them too. Measuring the bores after the engine is opened tells you for sure.

  • Blue smoke from the exhaust
  • Engine burns oil; you top up between services
  • Low or uneven compression
  • Fumes or oil mist from the breather (blow-by)
  • Piston slap or knocking when cold
  • Weak pickup and loss of power
How it's done

How reboring is done at the workshop

  1. Strip and clean

    The engine is opened down to the bare block and cleaned, so every bore can be checked properly.

  2. Measure every bore

    A bore gauge shows the wear, taper and out-of-round of each cylinder. These readings decide the work.

  3. Hone, rebore or sleeve

    Light wear may need only honing. Worn bores are rebored to the next oversize. A bore past its last oversize, or damaged, gets a new sleeve.

  4. Bore on the machine

    Each cylinder is bored on the boring machine to just under its final size, keeping the bore straight.

  5. Hone to size

    Honing brings each bore to its final size and leaves the crosshatch finish that new rings need to bed in and seal.

  6. Check the deck, then rebuild

    The block deck is checked for flatness and resurfaced if needed. Then new pistons and rings, sized to the finished bores, are fitted with the right clearances.

Choosing the fix

Rebore, sleeve, or only new rings?

Honing and new rings

When the bores are within the wear limit and only glazed or lightly marked.

Rebore and oversize pistons

When the bores are worn, tapered or scored but can still go to the next oversize, commonly 0.25 mm or 0.50 mm larger.

A new sleeve

When a bore is already at its last oversize, cracked or deeply scored. The sleeve is fitted, then bored and honed to size.

New rings alone in worn, oval bores rarely last: they can't seal, so the oil burning comes back. That's why the bores are measured first.

In-house machining

Machined in one place, on Samsani Road

Many workshops send the block out to a machine shop. At Standard Automobile Engineering, boring, honing, crankshaft grinding and cylinder head and deck work are done on the workshop's own machines, so the work stays in one place, and you can visit the workshop.

See the D17 job, before and after →

Cost

Engine reboring cost in Lahore

Reboring is part of a full engine rebuild. Estimated rebuild prices from the workshop, October 2026, for machining and genuine parts:

Car / engineEstimated (PKR)
Suzuki Mehran, Bolan, Alto 660, Every50,000 – 60,000
Daihatsu Cuore, Mira50,000 – 55,000
Suzuki Cultus, WagonR 100070,000 – 75,000
Toyota Corolla XLI/GLI, Vitz, Belta · Honda City, Civic, Fit70,000 – 1,00,000

Mechanic labour of about PKR 15,000 is extra. The final price is confirmed after inspection, before work starts. Engine already out? Call the workshop on 0333-6229700 to ask whether they can machine only the block, crank or head, and the price.

All engine overhaul prices, and what changes them →

Rebuild, or replace the car? Use the cost calculator →

Questions

Engine reboring: your questions

How much does engine reboring cost in Lahore?
Reboring is part of a full engine rebuild. Estimated workshop prices (October 2026) for machining and genuine parts: Suzuki Mehran, Bolan, Alto 660 and Every about PKR 50,000 – 60,000; Daihatsu Cuore and Mira about PKR 50,000 – 55,000; Suzuki Cultus and WagonR 1000 about PKR 70,000 – 75,000; Toyota Corolla XLI/GLI, Vitz and Belta, and Honda City, Civic and Fit, about PKR 70,000 – 1,00,000. Mechanic labour of about PKR 15,000 is extra. The final price is confirmed after inspection, before work starts.
How long does engine reboring take?
Reboring is done as part of the rebuild, and a full engine rebuild typically takes 4–5 days, depending on machining load and parts availability. You get a clear timeline up front and a photo at each stage on WhatsApp.
What does oversize 0.25 or 0.50 mean?
It is how much larger than standard the cylinder is bored, in millimetres. A bore taken 0.25 mm over gets pistons and rings made 0.25 mm larger, so they fit with the correct clearance. Each engine has a limit; after the last oversize, the cylinder needs a sleeve.
Can I change only the piston rings?
Only if the bores are within limits. In worn, tapered or oval bores, new rings can't seal for long and the oil burning comes back. The bores are measured first, and the readings decide.
Which engines do you rebore?
Our estimates cover Suzuki F8B (Mehran, Bolan), K10B (Cultus, WagonR 1000), K6A/R06A (Alto 660, Every), Toyota 1NZ/2NZ (Corolla XLI/GLI, Vitz, Belta), Honda (City, Fit, Civic) and Daihatsu EF (Cuore, Mira). Some engines can't take oversize pistons and need sleeves instead; the bore readings decide. For other engines, send the model, year and engine on WhatsApp.
Is reboring covered by the guarantee?
When Gaaribaan rebuilds your engine, the work is covered for 6 months or 10,000 km, whichever comes first, on the parts and labour we supplied. If the same covered fault returns in that time, we redo the work free.
Where is the workshop?
Standard Automobile Engineering, Shop # 22A, Shadiwal Chowk, Samsani Road, Lahore, near National Dry Cleaners — open Monday to Saturday, 10am to 8pm, with a Friday prayer break from 1pm to 3pm (Sunday closed). Please call 0333-6229700 before you come, or WhatsApp 0310-4538244.
Visit

Standard Automobile Engineering × Gaaribaan

Gaaribaan coordinates your rebuild end to end and stands behind the written guarantee. Machining is done by Standard Automobile Engineering on Samsani Road, Lahore — Haji Shafique Ahmed and M. Hassaan Shafique, with 40 years of family workshop experience.

Address
Shop # 22A, Block Revenue Society, Shadiwal Chowk, Samsani Road, Lahore 54000 · near National Dry Cleaners
Hours
Mon – Sat · 10am – 8pm · Friday prayer break 1 – 3pm · Sunday closed
Call (workshop)
0333-6229700
WhatsApp
0310-4538244

Please call before you come, so the right person is there.

Tell us about your engine

Send your car's model, year and problem on WhatsApp — voice notes welcome. We'll reply with an estimated price and the next step.